Guide
How to tell if you have hard water
The signs, what they mean in numbers, and how to confirm it.
Short answer
White spots that come back on glasses and shower glass, a chalky crust on the showerhead and inside the kettle, and soap that lathers poorly and leaves scum are the signs of hard water. Spotting starts once water is moderately hard, above 3.5 gpg (60 mg/L); kettle scale and soap trouble are typical above 7.0 gpg (120 mg/L). To confirm, get the number: your utility’s water quality report, the ZIP lookup, or a home test.
The signs, and the hardness that causes them
Every sign of hard water comes from the same two minerals, calcium and magnesium. They are left behind when water dries, they come out of solution when water is heated, and they react with soap before it can lather.
| Band | mg/L (ppm) | Grains per gallon | What you notice |
|---|---|---|---|
| Soft | 0 to 60 | 0.0 to 3.5 | No treatment needed. Soap lathers easily and there is no scale. |
| Moderately hard | 60 to 120 | 3.5 to 7.0 | Noticeable but usually tolerable. Some spotting on glassware. |
| Hard | 120 to 180 | 7.0 to 10.5 | Scale in kettles and on fixtures, more soap needed, shorter appliance life. |
| Very hard | over 180 | over 10.5 | Persistent scale, water heater efficiency loss, most households soften. |
- Spots on glasses and shower doors that look white or chalky once dry.
- Scale in the kettle and on the showerhead: heating water drives the dissolved calcium out as calcium carbonate, the white crust.
- Soap that will not lather, and a grey film or ring in the tub. Calcium and magnesium combine with soap into scum before any lather forms.
- Stiff laundry and dull hair, from the same soap and mineral residue.
- A water heater that rumbles, from scale collected at the bottom of the tank.
Things that look like hard water but are not
- Orange or brown stains are iron, and black ones manganese. A softener handles small amounts; the softener calculator adds them to the load.
- Blue or green stains under taps are copper, from pipes. That points to corrosive water, often soft water, not hard.
- Spots that vinegar will not shift can be silica, which acid does not dissolve. Watts warns in its conditioner specification that silica makes water spots difficult to remove.
Reading your utility’s report
Utilities publish hardness in their annual Consumer Confidence Report. Some give total hardness as calcium carbonate, which you can read straight off. Others list calcium and magnesium as metals, and those need converting: each mg/L of calcium counts as 2.5 mg/L of hardness, and each mg/L of magnesium as 4.1.
| Calcium 60 mg/L × 2.497 | 150 mg/L |
| Magnesium 20 mg/L × 4.118 | 82 mg/L |
| Total hardness as CaCO3 | 232 mg/L, 13.6 gpg |
| Classification | Very hard |
The hardness converter turns any of these into grains per gallon.
How common hard water is
Across the 3,110 counties in the public monitoring data, 55% have a median in the hard or very hard bands, and 29% are soft. The difference between states is large:
| State | Median mg/L | Median gpg |
|---|---|---|
| South Dakota | 403 | 23.5 |
| North Dakota | 314 | 18.3 |
| Arizona | 310 | 18.1 |
| Iowa | 310 | 18.1 |
| Illinois | 285 | 16.6 |
| Maine | 17 | 1.0 |
| South Carolina | 19 | 1.1 |
| Rhode Island | 21 | 1.2 |
| Mississippi | 21 | 1.2 |
| New Hampshire | 22 | 1.3 |
The figures are ambient water samples from the Water Quality Portal, not tap water. A utility may soften or blend its supply, and wells a mile apart can differ. In Maricopa County, Arizona, the median sample is 360 mg/L but a quarter are under 185 and a quarter over 621. In 93 counties a quarter of samples are soft and another quarter very hard. The county figure says what is likely; only your report or a test says what comes out of your tap. How to test water hardness at home covers strips, drop kits and the soap test.